Product was added to your cart

Cart

ASTM D 6693 – Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes – Testing Equipment

ManagerEquipment for Standards, Standards, Uncategorized

5 Apparatus5.1 Testing Machine—A testing machine of the constantrate-of-crosshead-movement type and comprising essentially the following:5.1.1 Fixed Member—A fixed or essentially stationary member carrying one grip.5.1.2 Movable Member—A movable member carrying a second grip.5.1.3 Grips—Grips for holding the test specimen between the fixed member and the movable member of the test apparatus can be either a…

Read More

ASTM D 2732 – Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting – Testing Equipment

ManagerEquipment for Standards, Standards

5 Apparatus5.1 Constant-Temperature Liquid Bath, capable of controlling accurately to ±0.5°C.5.1.1 The liquid for the bath should not plasticize or react with the specimens. Poly(ethylene glycol), glycerin, and water have been found to have wide applicability.5.2 Thermometer—ASTM Thermometer 1 °C conforming to the requirements as prescribed in Specification E 1.5.3 Square Metal Stamp, 100 by…

Read More

ASTM D 1414 Standard Test Methods for Rubber O-Rings – Testing Equipment

ManagerEquipment for Standards, Standards

General Methods5.1 Except as otherwise specified in these test methods for rubber O-rings, the following ASTM test methods applicable in general to vulcanized rubber, shall be complied with as required and are hereby made a part of these test methods:5.1.1 Tension Test—Test Methods D 412.5.1.2 Compression Set—Test Methods D 395.5.1.3 Low Temperature—Test Method D 1329.5.1.4…

Read More

How to Use Infield Tensile Tester for Butt Welds

ManagerHow to Use

LIMITED WARRANTY AHP PLASTIK MAKINA (AHP) warrants all products manufactured, sold and repaired by it to be free from defects in materials and workmanship, its obligation under this warranty being limited to repairing or replacing at its factory and new products, within 5 years after shipment, with the exception of purchased items (such as electronic…

Read More

ASTM D 1922 – Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method – Testing Equipment

ManagerEquipment for Standards, Standards

5 Apparatus5.1 Pendulum Impulse-Type Testing Apparatus, 5 consisting of the following:5.1.1 Stationary Clamp.5.1.2 Movable Clamp, carried on a pendulum, preferably formed by a sector of a wheel or circle, free to swing on a ball bearing or other substantially frictionless bearing. 5.1.3 Stop Catch, for holding the pendulum in a raised position and for releasing…

Read More

ASTM E8 – Tension Testing of Metallic Materials – Testing Equipment

ManagerEquipment for Standards, Standards

5 Apparatus5.1 Testing Machines—Machines used for tension testing shall conform to the requirements of Practices E 4. The forces used in determining tensile strength and yield strength shall be within the verified force application range of the testing machine as defined in Practices E 4.5.2 Gripping Devices:5.2.1 General—Various types of gripping devices may be used…

Read More

ASTM D 8117 – Standard Test Method for Oxidative Induction Time of Polyolefin Geosynthetics by Differential Scanning Calorimetry – Testing Equipment

ManagerEquipment for Standards, Standards

6 Apparatus6.1 Differential Scanning Calorimeter—As a minimum requirement, the thermal analysis equipment shall be capable of measuring heat flow of at least 10 mW full scale. The instrument recorder shall be capable of displaying heat flow or temperature differential on the y-axis and time on the x-axis. The time base must be accurate to 61…

Read More

Needle-Flame Test Method – Apparatus, Confirmatory Test Arrangement and Guidance IEC 60695-11-5

ManagerTechnology

The best method for testing electrotechnical products with regard to fire hazard is to duplicate exactly the conditions occurring in practice. In most instances this is not possible. Accordingly, for practical reasons, the testing of electrotechnical products with regard to fire hazard is best conducted by simulating as closely as possible the actual effects occurring…

Read More

Inline Ultrasonic Thickness Gage for PE Pipe Production Line

ManagerTechnology

Ultrasonic technology for thickness measurement is using ultrasound reflection time between our surface of the pipe and inner surface. If you calibrate the device for sound speed in the target material then machine can calculate the thickness. Sound speed in different materials depends mainly on material type and temperature. Of course when you calibrate device…

Read More
Menu